Jondell Builders Logo

We are Oswestry
based Builders and
Electrical Contractors

specialising in stove installations,
chimney lining and stonework

01691 882134 or 07817 602394

How to Build a Wood Stove Fire

Wood Burning Stove Image

By KMS Woodworks for

The key to using a wood stove efficiently is to build a hot fire. Isn’t all fire hot? Yes, but not hot enough.

Modern wood stoves can have burn efficiencies of 75 to 90 percent. These higher efficiencies are due to “secondary burns.” A secondary burn is where the hydrocarbons in the smoke are re-ignited before leaving the stove, thereby reducing emissions and releasing more heat.

For this to occur, a hot fire of 1000 – 1200 degrees F is required. Hot fires also reduce the build up of creosote in the stove and chimney pipe.

How Wood Burns

Rather than explaining advanced physics and principles of thermodynamics here, I’ll share what I have learned from a lifetime of using wood stoves:

Contrary to what most people believe, the wood itself does not burn, but rather the combustible gasses that are released from the wood when it is heated. If you watch closely, you can see little “jets” of gas form on the ends of logs. These resemble minute blowtorches, and the heat from this burning gas releases more gas and keeps the fire going.

The key to building a fire with plenty of combustible gas is to start it with ample kindling. Kindling is simply smaller bits of firewood. Smaller bits allow more air contact, and thus faster combustion. A good pile of kindling will get the stove heated quickly, and then allow larger logs to start burning faster.

Well-seasoned Wood

Before wood will burn cleanly, the moisture needs to be removed (by drying) or driven off (by burning).

If your wood is hissing or you can see bubbles forming on the log ends, your wood is not completely dry and its burning will be inefficient. This moisture and unburned “gas” can cause a smoky fire and lead to creosote build up.

A lot of the beetle-kill firewood that is being harvested has been dead standing for some time and is pretty much ready to go. If you cut living timber, the rule of thumb is to season (dry) it for about a year prior to use. Obviously split wood will dry more quickly than “rounds,” as more surface area is exposed to the air.

Preheating the flue is key to preventing creosote accumulation.

A fast, hot fire will preheat the flue and reduce the chance that creosote will accumulate. This preheating will also set the flue up to “draw” properly. Once airflow has been established in the flue, the intake ports on the stove will allow sufficient air to enter and to burn more completely.

The key to low creosote buildup is to have the chimney temperatures well above boiling to keep the wood’s moisture in the gas phase before it leaves the pipe. If the pipe is cold, these unburned gases, moisture, and carbon products can condense on the inside of your flue.

Smoke and Coals

When a fire is first started, it will smoke. These are the combustion gases that have not yet reached combustion temperatures. Sometimes you can watch this smoke “burst” into flames when it has become hot enough.

On winter evenings, looking over my town, you can often see various plumes of smoke as people get their evening fires started. Once the fire is well established, there should be very little, if any, smoke.

If your fire is still smoking by the time your kindling has been used up, your firewood may be too wet or your air supply too low. When starting a fire in a wood stove, it is best to fully open all vents or even leave the door ajar to allow the fire to burn with the most robust exposure to oxygen.

Timing your Fire Right

In my big stove, the start-up takes about 15 minutes. We like to start with smaller bits of wood for the start-up and then toss in the larger pieces. After about 30 minutes, a coal bed starts to form, and we close down the catalytic vent and set the intakes to about 50 percent. Once the stove is in this state we can add large pieces every couple of hours.

On really cold nights, or when the winds are cranking, we load up extra logs before bed. In the morning, we can often resurrect a few coals and start all over again. Maintaining a shallow ash bed (about 2″) actually allows for better fires.

We clear out the ash after a few weeks worth of fires. If your stove is running clean, the hot ash buildup should be minimal.

Remember to always place ashes in metal ash buckets, never in paper bags. Once or twice each year, we read in the paper about some home fire due to improper ash storage.